PicoFlow - 低固气比状态下的固体物料流量测量

当前位置:Home · 产品介绍 · PicoFlow - 低固气比状态下的固体物料流量测量
 

PicoFlow -
低固气比状态下的固体物料流量测量

在非常低的管道物料填充比输送状态下的固体粉末流量测量

  • 在气力输送状态下,流量可以测量到100kg/h(依赖于实际应用)
  • 在自由落体状态下至少需要2m/s的下落速度(接近 0.25cm的自有落体高度)
  • 应用于粉尘测量设备不能测量以及质量流量测量设备标称测量范围之外的系列应用

 

 

Use

PicoFlow was specially developed for measuring powder flows in transport lines with very low material concentrations.

PicoFlow is particularly good in pneumatic applications but will also work reliably in free-fall applications with drop speeds of at least 2 m/s.

The measuring system delivers absolute measurements (after calibration)
in g/h or kg/h.

A special air purging system is also available as an option.
This is used for materials which tend to bake onto surfaces.

Function

The measuring principle of the PicoFlow is based on the electrodynamic measuring effect.
A ceramic coating on the very short antenna prevents sensor wear.
Specially developed hardware and software allows the measurements to be linearised.

Mounting and Installation

The PicoFlow can be installed in metallic ducts and pipelines.

It should be installed as far as possible away from curves and other fittings such as valves and slides.The distance between the sensor rod and fittings in the duct should be at least three times the duct diameter in every flow direction.

Non-metallic ducts must be cased with a metal sleeve, a metal foil or a tight-mesh metal grille over a length of at least five times the duct diameter.
After deciding the installation location, drill a hole in the duct wall where the supplied weld-on socket can be welded perpendicular to the pipe. Then screw the sensor rod into the socket using the screw-in thread.

Technical Data

Sensor Measurement range From 100 g/h to 100 kg/h (depends on application)
  Process temperature Standard: 150 °C; Optional: max. 500 °C
  Pressure Max. 2 bar (Optional: up to 25 bar)
  Flow velocity Min. 2 m/sec
  Humidity 60 % RH or less (non-condensing)
  Measurement principle Electrodynamics
  Ambient temperature -20 … +60 °C
  Sensor rod Material: Stainless steel, AL2O3 ceramic 99,7 %; Length: depends on application
  Housing material Aluminium
  Protection type IP 66; ATEX: Cat. 1/2 GD
  Electrial connection Connection chamber DIN M 20
  Switch output measurement alarm Relay with switchover contact - max. 250 V/AC, 1A
Not on EX devices Cat. 1 and 2
  Weight Ca. 1.5 kg
     
Transmitter (field housing) Power supply 110/230 V, 50 Hz (optional 24 V DC)
  Power consumption 20 W / 24 VA
  Protection type IP 65 to EN 60 529/10.91
  Ambient temperature -10 ... + 45 °C
  Dimensions 258 x 237 x 174 (W x H x D)
  Weight approx. 2.5 kg
  Interface RS 485 / RS 232 C (ModBus)
  Cable screw connectors 3 x M 16 (4.5 - 10 mm Ø)
  Connection terminals cable cross-section 0.2 - 2.5 mm² [AWG 24-14]
  Current output 4 ... 20 mA (0 ... 20 mA), load < 500 Ω
  Switch output measurement alarm Relay with switchover contact - max. 250 V AC, 1 A
  Data backup Flash memory
  Pulse output Open collector - max. 30 V, 20 mA
     
Transmitter (DIN rail) Power supply 24 V DC ± 10 %
  Power consumption 20 W / 24 VA
  Protection type IP 40 to EN 60 529
  Ambient temperature -10 ... +45 °C
  Dimensions 23 x 90 x 118 (W x H x D)
  Weight Approx. 172 g
  Connection terminals cable cross-section 0.2 - 2.5 mm² [AWG 24-14]
  Current output 4 ... 20 mA (0 ... 20 mA), load < 500 Ω
  Switch output measurement alarm Relay with switchover contact - max. 250 V AC, 1 A
  Data backup Flash memory
  Pulse output Open collector - max. 30 V, 20 mA
 
 

快速导航:您想查询什么?