M-Sens 2 FD - 在线水分测量

当前位置:Home · 产品介绍 · M-Sens 2 FD - 在线水分测量
 

M-Sens 2 FD-
在线水分测量(含流动探测功能)

应用微波传感器技术连续在线测量物料的水分含量,同时兼具固体物料流动探测功能
安装简便(可安装于料仓出口,螺旋给料机,皮带输送机,斜槽等设备上)

  • 水份测量范围0…65%(根据被测物料有所不同)
  • 测量准确度0.1%
  • 实时在线水分测量
  • 物料流动监测报警
  • 不受物料颜色的影响
  • ATEX防爆认证
  • 测量表面和毛细水分

Use

The M-Sens 2 is used for the continuous measurement of humidity on solids
of all kinds.
 
The M-Sens 2 sensor can ideally be used, for example in container outlets, conveyor belts, conveyor screws, mixers and conveyor dryers.
 
It is important that the measuring surface of the sensor is always covered with material. The M-Sens 2 is a contact-measuring procedure. The ceramic disc (measuring surface) must always be covered with material.

Function

The M-Sens 2-sensor works with precise high-frequency measurements and direct digitalisation of the measurement values and thus a high resolution.
Since the surface and capillary humidity of a material has a strong influence on its dielectric constant, the humidity can be determined exactly given a constant medium bulk density. By way of support, any fluctuations of the measuring value caused by the bulk density are balanced through an internal filter function. Temperature-related fluctuations of the measuring value are automatically compensated by the sensor. The calibration of the system can easily be carried out by the operator. On the installed system, the calibration is a matter of pushing a button and entering the humidity reference value.

Mounting and Installation

Flexible positioning
The M-Sens 2 was developed to offer maximum flexibility during assembly. The following aspects should be taken into account in the positioning of the probe: The measuring field penetrates the densest materials (e. g. sand). With a minimum depth of 120 mm, the probe should always be directed at the material to avoid reflection problems. 
    
Installation situations
Container

For a simple installation, a standard connection flange is available.  

 

 

 

    

    
Conveyor belt

Measurement of material moisture on a conveyor belt.
A constant material height is generated by attaching a material skimmer. This offers ideal conditions for an online measurement.

 

 

    
      

 

 

 

 

 

The installation in the lower third of a conveyor screw has the advantage that the material volume that passes over the sensor is almost constant, allowing for an optimal measurement. The movement of the auger flights is hidden.

 

 

    
      

 

 

 

Free fall pipe


To be able to measure in free fall pipes or inclined pipes (chutes) with the M-Sens 2, it is possible to gather material in front of the probe in the short term, for the duration the measurement, with a catching mechanism. After the measurement, the flap will open again and allows the gathered material to continue to drop. The measuring process can be permanently repeated in short or long intervals according to requirements.    

Technical Data

Sensor Housing Stainless steel 1.4571
  Sensor surface Ceramic
  Protection category IP 67 according to EN 60529
  Ex-protection (optional) Zone 20 (dust), zone 0 (gas)
  Material ambient temperature 0 ... + 120 °C
  Working pressure max. 10 bar
  Power consumption 0.6 W
  Weight approx. 1.0 kg
  Response time 0.1 seconds
  Measuring range 0... 65 % residual moisture (depending on material)
  Accuracy 0.1 % absolutely in the calibrated measuring range
  Connecting cable shielded cable 4-wired, 0.25 mm²
     
Transmitter Power supply 110/230 V AC (50 Hz) 24 V DC
  Power consumption 20 W / 24 V
  Current consumption max. 1 A at 24 V
  Protection category IP 65 according to EN 60529/10.91
  Operating temperature - 10... + 45 °C
  Dimensions 258 x 237 x 174 mm (W x H x D)
  Weight approx. 2.5 kg
  Interface RS 232, RS 485
  Cable glands 3x M16 (4.5-10 mm Ø)
  Cable cross section 0.2 - 2.5 mm² [AWG 24-14]
  Current output signal 1 x 4 ... 20 mA (0 ... 20 mA), load < 500 Ohm
  Switched output measuring alarm Relay with two-way contact max. 250 V AC, 1 A
  Digital inputs 2 inputs for active external control signals
  Data protection Flash
     

Application Form

 
 

快速导航:您想查询什么?