MaxxFlow HTC - Medición de flujo de sólidos

Ellos están aquí:Home · Productos · MaxxFlow HTC - Medición de flujo de sólidos
 

MaxxFlow HTC -
Medición de altos flujos másicos de sólidos a granel en caída libre o transporte neumático en fase diluida

Medición de altos flujos másicos de sólidos a granel en caída libre o transporte neumático en fase diluida después de elementos de alimentación, como por ejemplo, cintas transportadoras, aerodeslizadores, válvulas rotativas, elevadores de cangilones.   

  • La mayoría de los sólidos no metálicos pueden ser medidos
  • Puede ser instalado en tuberías o conductos circulares
  • Sin límite máximo de caudal másico.
  • Resistente hasta 10 bar de presión 
  • 100 % Hermético al polvo    
  • Sin elementos que puedan entorpecer el flujo (Sin partes móviles) o puedan generar compactaciones u obturaciones (interno cerámico resistente a la abrasión).  
  • La medición del caudal másico es independiente de las características del flujo 
  • Temperature máxima, 120°C
  • Puede ser instalado en ángulo sin necesidad de tener que adecuar la instalación.
  • Equipo muy compacto, 220 mm de largo para el DN 100, 290 mm para el DN 150 y de 310 mm para el DN 200
  • Sin partes móviles, sin necesidad de mantenimiento

Use

The MaxxFlow HTC is specially developed for the flow measurement of dry bulk solids during high-volume throughput. Due to its completely open profile and its low installation height, the MaxxFlow HTC is especially suitable in situation in which it was previously only possible to use complicated or expensive mechanical solutions, e. g. impact plates or measuring chutes.

The installation of the MaxxFlow HTC takes place independently of the direction of the line (vertical/inclined), but always after mechanical conveyor elements,
e. g. rotary feeder, screw conveyors, air slides or chain conveyors.

Function

After the conveyor, the material to be measured falls or slides through an inlet path and runs through the sensor. During the throughput, the MaxxFlow HTC records the material type and speed. Since the material falls from a constant height after emerging from the conveyor element, the speed of the product stream is accelerated, but is constant at the installation position of the sensor.
Due to this constant speed, the speed measurement does not need to be activated in every case, but can be calculated as a constant depending on the height of the fall. The mass flow is determined as follows:

Q (kg/s)   =   K (kg/m3)   x   v (m/s)   x   A (m2)

Through the input coupling of a high-frequency, electro-magnetic alternating field, a homogenous measuring field is generated in the measuring tube.
The measuring tube (interior tube of the sensor) consists of wear-resistant Al2O3 ceramics. Dry bulk solids inside the measuring field reduce the amplitude of the alternating field.
This leads to a measuring signal that is in proportion to the concentration of the dry bulk solids in the sensor (kg/m3).

If the material speed varies, for example due to a change in initial speed, then this can also be measured. 
This takes place through a runtime measurement with the help of two additional electrodes behind the interior ceramics tube.

 

 

Mounting and Installation

A complete measuring station consists of these components:

•    Measuring feeder for installation in the conveyor line
•    Transmitter

The measuring feeder is available in sizes DN 100, DN 150 mm and DN 200 mm.
On request the components inlet path (between conveyor element and sensor) and gate valve (for calibration) can also be configured and supplied.

The transmitter is connected to the sensor using 4-wired, shielded cable.
The maximum distance between measuring feeder and transmitter is 300 m.

Technical Data

Sensor Housing Steel St 52, powder-coated (optional stainless steel 1.4571 NW 100/150/200 mm, flange according EN 1092-1 / PN 10
  Inner pipe Ceramic AL2O3
  Protection category IP 65
  Operating temperature Sensor electronic:
0 ... + 60 °C
Sensor pipe:
- 20 ... + 120 °C
  Max. working pressure 1 bar, optional 10 bar
  Working frequency 88 kHz
  Transmitting power Max. 2 mW
  Weight Depending on model
  Accuracy ± 3 % (based on end of measuring range and calibrated material)
     
Transmitter (Field housing) Power supply 110/240 V AC, 50 Hz, optional 24 V DC
  Power comsumption 20 W / 24 VA
  Operating temperature - 10... + 45 °C
  Dimensions 258 x 237 x 174 mm (W x H x D)
  Weight Approx. 2.5 kg
     
Additional data RS 485 interface ModBus
  Terminal clamp wire size 0.2 - 2.5 mm_ [AWG 24-14]
  Current output signal 2 x 4 ... 20 mA (0 ... 20 mA), load < 500 Ohm
  Serial output RS 485, ModBus protocol
  Data backup Flash memory
  Cable glands 3 x M 16 (4.5 - 10 mm Ø)
     

Application examples

Click on a desired application example to navigate to a detailed description.

Medición de flujo de sólidos

Mass flow measurement
of raw meal

Mass flow measurement of potato starch
in free fall prefeeding chain conveyors

Mass flow measurement of raw meal
in free fall after air slide

Mass flow measurement of salt
in free fall pre feeding chain conveyor

Mass flow measurement 
of raw meal after dosing roller

Mass flow measurement for
truck loading

Material admixture
in building material industry

 
 

Quickfinder: Búsqueda rápida